Related technologies




Redundancyedit

While a group of bits malfunction may be resolved by error detection and correction mechanisms (see above), storage device malfunction requires different solutions. The following solutions are commonly used and valid for most storage devices:

  • Device mirroring (replication) – A common solution to the problem is constantly maintaining an identical copy of device content on another device (typically of a same type). The downside is that this doubles the storage, and both devices (copies) need to be updated simultaneously with some overhead and possibly some delays. The upside is possible concurrent read of a same data group by two independent processes, which increases performance. When one of the replicated devices is detected to be defective, the other copy is still operational, and is being utilized to generate a new copy on another device (usually available operational in a pool of stand-by devices for this purpose).
  • Redundant array of independent disks (RAID) – This method generalizes the device mirroring above by allowing one device in a group of N devices to fail and be replaced with the content restored (Device mirroring is RAID with N=2). RAID groups of N=5 or N=6 are common. N>2 saves storage, when comparing with N=2, at the cost of more processing during both regular operation (with often reduced performance) and defective device replacement.

Device mirroring and typical RAID are designed to handle a single device failure in the RAID group of devices. However, if a second failure occurs before the RAID group is completely repaired from the first failure, then data can be lost. The probability of a single failure is typically small. Thus the probability of two failures in a same RAID group in time proximity is much smaller (approximately the probability squared, i.e., multiplied by itself). If a database cannot tolerate even such smaller probability of data loss, then the RAID group itself is replicated (mirrored). In many cases such mirroring is done geographically remotely, in a different storage array, to handle also recovery from disasters (see disaster recovery above).

Network connectivityedit

A secondary or tertiary storage may connect to a computer utilizing computer networks. This concept does not pertain to the primary storage, which is shared between multiple processors to a lesser degree.

  • Direct-attached storage (DAS) is a traditional mass storage, that does not use any network. This is still a most popular approach. This retronym was coined recently, together with NAS and SAN.
  • Network-attached storage (NAS) is mass storage attached to a computer which another computer can access at file level over a local area network, a private wide area network, or in the case of online file storage, over the Internet. NAS is commonly associated with the NFS and CIFS/SMB protocols.
  • Storage area network (SAN) is a specialized network, that provides other computers with storage capacity. The crucial difference between NAS and SAN, is that NAS presents and manages file systems to client computers, while SAN provides access at block-addressing (raw) level, leaving it to attaching systems to manage data or file systems within the provided capacity. SAN is commonly associated with Fibre Channel networks.

Robotic storageedit

Large quantities of individual magnetic tapes, and optical or magneto-optical discs may be stored in robotic tertiary storage devices. In tape storage field they are known as tape libraries, and in optical storage field optical jukeboxes, or optical disk libraries per analogy. The smallest forms of either technology containing just one drive device are referred to as autoloaders or autochangers.

Robotic-access storage devices may have a number of slots, each holding individual media, and usually one or more picking robots that traverse the slots and load media to built-in drives. The arrangement of the slots and picking devices affects performance. Important characteristics of such storage are possible expansion options: adding slots, modules, drives, robots. Tape libraries may have from 10 to more than 100,000 slots, and provide terabytes or petabytes of near-line information. Optical jukeboxes are somewhat smaller solutions, up to 1,000 slots.

Robotic storage is used for backups, and for high-capacity archives in imaging, medical, and video industries. Hierarchical storage management is a most known archiving strategy of automatically migrating long-unused files from fast hard disk storage to libraries or jukeboxes. If the files are needed, they are retrieved back to disk.

Comments

Post a Comment

Popular posts from this blog

Characteristics of storage

Image
Storage technologies at all levels of the storage hierarchy can be differentiated by evaluating certain core characteristics as well as measuring characteristics specific to a particular implementation. These core characteristics are volatility, mutability, accessibility, and addressability. For any particular implementation of any storage technology, the characteristics worth measuring are capacity and performance. Volatility edit Non-volatile memory retains the stored information even if not constantly supplied with electric power. It is suitable for long-term storage of information. Volatile memory requires constant power to maintain the stored information. The fastest memory technologies are volatile ones, although that is not a universal rule. Since the primary storage is required to be very fast, it predominantly uses volatile memory. Dynamic random-access memory is a form of volatile memory that also requires the stored information to be periodically reread and rewritten, or ref
Read more

Functionality

Image
Without a significant amount of memory, a computer would merely be able to perform fixed operations and immediately output the result. It would have to be reconfigured to change its behavior. This is acceptable for devices such as desk calculators, digital signal processors, and other specialized devices. Von Neumann machines differ in having a memory in which they store their operating instructions and data.: 20 Such computers are more versatile in that they do not need to have their hardware reconfigured for each new program, but can simply be reprogrammed with new in-memory instructions; they also tend to be simpler to design, in that a relatively simple processor may keep state between successive computations to build up complex procedural results. Most modern computers are von Neumann machines.
Read more

Hierarchy of storage

Image
This article appears to contradict the article Memory hierarchy . Please see discussion on the linked talk page. ( March 2013 ) (Learn how and when to remove this template message) Generally, the lower a storage is in the hierarchy, the lesser its bandwidth and the greater its access latency is from the CPU. This traditional division of storage to primary, secondary, tertiary and off-line storage is also guided by cost per bit. In contemporary usage, "memory" is usually semiconductor storage read-write random-access memory, typically DRAM (dynamic RAM) or other forms of fast but temporary storage. "Storage" consists of storage devices and their media not directly accessible by the CPU (secondary or tertiary storage), typically hard disk drives, optical disc drives, and other devices slower than RAM but non-volatile (retaining contents when powered down). Historically, memory has been called core memory , main memory , real storage or internal memory . Meanwhile
Read more